Glasgow/Modeling

From 2007.igem.org

(Difference between revisions)
Line 44: Line 44:
The Multi-Parametric and Initial concentration analysis Sensitivity (Minicap) package is a Matlab function which executes a chosen Dynamic or Stochastic system for a defined number of different variable values across any desired range. The ''subject'' of analysis can either be constants in the user's system (eg. parameters in a biological system) usually termed MPSA, or initial values of the variables in the user's system (eg. initial substrate concentrations) termed ISCSA. The program will output a plot for each variable showing a comparison of ''acceptable'' and ''unacceptable'' samples across the subject's range with 3 calculated quantitative comparison figures: the ''Correlation Coefficient'', the ''area'' between acceptable and unacceptable curves, and the ''standard deviation of the gradient'' of the acceptable plot. The comparative and intrinsic sensitivity of each chosen subject is thus highlighted. A plot showing the trend of the ''Substrate-of-Interest'' over time is also displayed.  
The Multi-Parametric and Initial concentration analysis Sensitivity (Minicap) package is a Matlab function which executes a chosen Dynamic or Stochastic system for a defined number of different variable values across any desired range. The ''subject'' of analysis can either be constants in the user's system (eg. parameters in a biological system) usually termed MPSA, or initial values of the variables in the user's system (eg. initial substrate concentrations) termed ISCSA. The program will output a plot for each variable showing a comparison of ''acceptable'' and ''unacceptable'' samples across the subject's range with 3 calculated quantitative comparison figures: the ''Correlation Coefficient'', the ''area'' between acceptable and unacceptable curves, and the ''standard deviation of the gradient'' of the acceptable plot. The comparative and intrinsic sensitivity of each chosen subject is thus highlighted. A plot showing the trend of the ''Substrate-of-Interest'' over time is also displayed.  
-
To see the full PDF report on Minicap click here. [[Minicap.pdf| click here]]
+
To see the full PDF report on Minicap click here [[Minicap.pdf| click here]].

Revision as of 10:38, 7 September 2007

https://static.igem.org/mediawiki/2007/thumb/c/cc/Uog.jpg/50px-Uog.jpg Back To
Glasgow's
Main Page

Trial model for the PDntR|S promoter

The current model that will be used for modeling purposes will use the three following equations to model the simple system as shown in Figure 1. The reasons for using these modified equations are discussed below.

Screenshot1.jpg

Discussion

The equation for the change of DntR|S within the system could be modelled by Equation 4

Screenshot2.jpg

At the beginning of the reaction DntR will have an unknown constant value as it cannot be measured physically in the laboratory. As the DntR will have a constant value the DntR and kb can be replaced by another constant kb’ as shown

Screenshot3.jpg

By substituting Equation 5 into Equation 4 gives

Screenshot4.jpg

However it is clear from Equation 6 that as the signal increases the DntR|S will increase without ever reaching a saturation limit. It was decided that the equation should be changed to utilize Michaelis-Menten. This means that a saturation limit will now be possible as shown in Equation 1.


Next it is important to note that the signal equation includes a term for the degradation of the signal as this is possible in the physical model. This equation also includes a term for the binding and a term for the unbinding as shown in Equation 2.


Also it should be noted that in this model XGAL is ignored, this is because the level of blue that is measured is proportional to the LacZ produced. By ignoring XGAL it will simplify the system equations.


Another point to note is that in this model of the system the transcription and the translation steps have been ‘lumped’ together by using Michaelis-Menten rather than modeling these biological steps separately.


Simplemodel.jpg
Figure 1


Minicap Sensitivity Analysis Program Package
The Multi-Parametric and Initial concentration analysis Sensitivity (Minicap) package is a Matlab function which executes a chosen Dynamic or Stochastic system for a defined number of different variable values across any desired range. The subject of analysis can either be constants in the user's system (eg. parameters in a biological system) usually termed MPSA, or initial values of the variables in the user's system (eg. initial substrate concentrations) termed ISCSA. The program will output a plot for each variable showing a comparison of acceptable and unacceptable samples across the subject's range with 3 calculated quantitative comparison figures: the Correlation Coefficient, the area between acceptable and unacceptable curves, and the standard deviation of the gradient of the acceptable plot. The comparative and intrinsic sensitivity of each chosen subject is thus highlighted. A plot showing the trend of the Substrate-of-Interest over time is also displayed.

To see the full PDF report on Minicap click here click here.