Tokyo/Formulation/1.toggle model
From 2007.igem.org
| Line 24: | Line 24: | ||
<br>[[Image:toggle1.jpg|303px|]][[Image:toggle2.jpg|300px|]][[Image:Toggle1-4.jpg |300px|]] | <br>[[Image:toggle1.jpg|303px|]][[Image:toggle2.jpg|300px|]][[Image:Toggle1-4.jpg |300px|]] | ||
| - | + | <br>First,we carried out kinetic simulations in the condition of Fig●.The results are shown in Fig●. | |
| - | <br>First,we | + | |
<br> 1. (Ra:low , Rb:high) 2. (Ra:high , Rb:low) 3. (Ra:middle , Rb:middle) | <br> 1. (Ra:low , Rb:high) 2. (Ra:high , Rb:low) 3. (Ra:middle , Rb:middle) | ||
<br>[[Image:toggle3.jpg|200px|]] [[Image:toggle4.JPG|200px|]] [[Image:toggle5.JPG|200px|]][[Image:toggle1-1.jpg|200px|]] | <br>[[Image:toggle3.jpg|200px|]] [[Image:toggle4.JPG|200px|]] [[Image:toggle5.JPG|200px|]][[Image:toggle1-1.jpg|200px|]] | ||
| - | <br> | + | <br>Fig● indicate that when the initial condition is (Ra,Rb)=(0.0,2.5),which is near stable equilibrium point B, the values of Ra and Rb goes to stable equilibrium point B and when the initial condition is (Ra,Rb)=(2.5,0.0),which is near stable equilibrium point A, the values of Ra and Rb goes to stable equilibrium point B. |
| - | + | ||
| - | + | ||
| - | + | ||
| - | <br>Next, | + | <br>Next,when the number of stable equilibrium point is one, the result of simulation are shown in Fig● |
| - | + | ||
<br>[[Image:toggle6.JPG|200px|]] [[Image:Toggle7.JPG|200px|]] [[Image:toggle8.JPG|200px|]][[Image:toggle1-2.jpg|200px|]] | <br>[[Image:toggle6.JPG|200px|]] [[Image:Toggle7.JPG|200px|]] [[Image:toggle8.JPG|200px|]][[Image:toggle1-2.jpg|200px|]] | ||
Revision as of 01:35, 24 October 2007
1.toggle model
First,the ordinary differential equations(ODEs) of the toggle switch were derived as
These equations were normalized as follows:
In the steady state,time derivatives are zero:
As a result,the nullclines of this system were derived as
which indicate the nullclines of the system shown in Fig●．
About parameters,we use three sets of parameters.
1)the maximum expression rate of repressor A and repressor B is balanced,and hill coefficient of both A and B is three.
2)the maximum expression rate of repressor A and repressor B is equal,and hill coefficient of A is one.
3)the maximum expression rate of repressor A and repressor B is not balanced,and hill coefficient of both A and B is three.
First,we carried out kinetic simulations in the condition of Fig●.The results are shown in Fig●.
1. (Ra:low , Rb:high) 2. (Ra:high , Rb:low) 3. (Ra:middle , Rb:middle)
Fig● indicate that when the initial condition is (Ra,Rb)=(0.0,2.5),which is near stable equilibrium point B, the values of Ra and Rb goes to stable equilibrium point B and when the initial condition is (Ra,Rb)=(2.5,0.0),which is near stable equilibrium point A, the values of Ra and Rb goes to stable equilibrium point B.
Next,when the number of stable equilibrium point is one, the result of simulation are shown in Fig●
安定点が一つしかない場合は，安定点B付近から始めてもA状態で安定化してしまうのが分かる．
As a result,taking two stable status need the phaseplane of two stable equilibrium points and we have to set proper parameters.
