Glasgow/Modeling
From 2007.igem.org
| Line 42: | Line 42: | ||
'''Minicap Sensitivity Analysis Program Package'''<br> | '''Minicap Sensitivity Analysis Program Package'''<br> | ||
| - | The Multi-Parametric and Initial concentration analysis Sensitivity (Minicap) package is a Matlab function which executes a chosen Dynamic or Stochastic system for a defined number of different variable values across any desired range. The ''subject'' of analysis can either be constants in the user's system (eg. parameters in a biological system) usually termed MPSA, or initial values of the variables in the user's system (eg. initial substrate concentrations) termed ISCSA. The program will output a plot for each variable showing a comparison of ''acceptable and ''unacceptable'' samples across the subject's range with 3 calculated quantitative comparison figures: the ''Correlation Coefficient'', the ''area'' between acceptable and unacceptable curves, and the ''standard deviation of the gradient'' of the acceptable plot. The comparative and intrinsic sensitivity of each chosen subject is thus highlighted. A plot showing the trend of the ''Substrate-of-Interest'' over time is also displayed. | + | The Multi-Parametric and Initial concentration analysis Sensitivity (Minicap) package is a Matlab function which executes a chosen Dynamic or Stochastic system for a defined number of different variable values across any desired range. The ''subject'' of analysis can either be constants in the user's system (eg. parameters in a biological system) usually termed MPSA, or initial values of the variables in the user's system (eg. initial substrate concentrations) termed ISCSA. The program will output a plot for each variable showing a comparison of ''acceptable'' and ''unacceptable'' samples across the subject's range with 3 calculated quantitative comparison figures: the ''Correlation Coefficient'', the ''area'' between acceptable and unacceptable curves, and the ''standard deviation of the gradient'' of the acceptable plot. The comparative and intrinsic sensitivity of each chosen subject is thus highlighted. A plot showing the trend of the ''Substrate-of-Interest'' over time is also displayed. |
To see the full PDF report on Minicap click here. [[Glasgow/|<font face=georgia color=#3366CC size=4> Read Toby's <br> 59 Second <br> Interview </font>]] | To see the full PDF report on Minicap click here. [[Glasgow/|<font face=georgia color=#3366CC size=4> Read Toby's <br> 59 Second <br> Interview </font>]] | ||
Revision as of 10:32, 7 September 2007
| https://static.igem.org/mediawiki/2007/thumb/c/cc/Uog.jpg/50px-Uog.jpg | Back To Glasgow's Main Page |
|---|
Trial model for the PDntR|S promoter
The current model that will be used for modeling purposes will use the three following equations to model the simple system as shown in Figure 1. The reasons for using these modified equations are discussed below.
Discussion
The equation for the change of DntR|S within the system could be modelled by Equation 4
At the beginning of the reaction DntR will have an unknown constant value as it cannot be measured physically in the laboratory. As the DntR will have a constant value the DntR and kb can be replaced by another constant kb’ as shown
By substituting Equation 5 into Equation 4 gives
However it is clear from Equation 6 that as the signal increases the DntR|S will increase without ever reaching a saturation limit. It was decided that the equation should be changed to utilize Michaelis-Menten. This means that a saturation limit will now be possible as shown in Equation 1.
Next it is important to note that the signal equation includes a term for the degradation of the signal as this is possible in the physical model. This equation also includes a term for the binding and a term for the unbinding as shown in Equation 2.
Also it should be noted that in this model XGAL is ignored, this is because the level of blue that is measured is proportional to the LacZ produced. By ignoring XGAL it will simplify the system equations.
Another point to note is that in this model of the system the transcription and the translation steps have been ‘lumped’ together by using Michaelis-Menten rather than modeling these biological steps separately.
Minicap Sensitivity Analysis Program Package
The Multi-Parametric and Initial concentration analysis Sensitivity (Minicap) package is a Matlab function which executes a chosen Dynamic or Stochastic system for a defined number of different variable values across any desired range. The subject of analysis can either be constants in the user's system (eg. parameters in a biological system) usually termed MPSA, or initial values of the variables in the user's system (eg. initial substrate concentrations) termed ISCSA. The program will output a plot for each variable showing a comparison of acceptable and unacceptable samples across the subject's range with 3 calculated quantitative comparison figures: the Correlation Coefficient, the area between acceptable and unacceptable curves, and the standard deviation of the gradient of the acceptable plot. The comparative and intrinsic sensitivity of each chosen subject is thus highlighted. A plot showing the trend of the Substrate-of-Interest over time is also displayed.
To see the full PDF report on Minicap click here. Read Toby's
59 Second
Interview
