ETHZ/FlipFlop

From 2007.igem.org

< ETHZ
Revision as of 14:27, 26 October 2007 by Cbergeles (Talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)

ETHZ banner.png

 


An Engineer's View on Biological Learning

Fig. 1: Schematic view on the system implemented by logical gates.

An equivalent system behavior can be realized using [http://en.wikipedia.org/wiki/Flip-flop_%28electronics%29 flip-flops], implemented by [http://en.wikipedia.org/wiki/Logic_gate logical gates]:

As already shown in the finite state machine representation (FSM), the proposed system consists of three different states and recognizes four different inputs. In total, this adds up to twelve different transitions. In order to implement these twelve transitions with a digital system, at least four binary inputs are required (allowing for a maximum of 16 transitions) and since the proposed system has four different outputs, at least two binary outputs are required. Here, we chose an implementation using two JK flip-flops consisting of [http://en.wikipedia.org/wiki/Nand_gate#NAND_gate NAND gates]. An overview of the resulting system is given in Fig. 1 and details concerning flip-flop and NAND gate behavior are given in the following table:

J K Qnext A B A NAND B
0 0 Qprev 0 0 1
0 1 0 0 1 1
1 0 1 1 0 1
1 1 [http://en.wikipedia.org/wiki/Inverse_%28logic%29 ¬Qprev] 1 1 0

When initializing the system we set both outputs Q to zero. The mapping from inputs ( AHL+IPTG, IPTG, AHL+aTc, aTc) and system states ( q0, q1, q2) to the binary inputs (J1, K1, J2, K2) is given by following table:

states/inputs AHL+IPTG IPTG AHL+aTc aTc
q0 J1=0, K1=1, J2=1, K2=0 J1=0, K1=0, J2=0, K2=1 J1=1, K1=0, J2=0, K2=1 J1=0, K1=1, J2=0, K2=1
q1 J1=0, K1=1, J2=1, K2=0 J1=0, K1=0, J2=0, K2=1 J1=0, K1=1, J2=0, K2=0 J1=0, K1=0, J2=1, K2=1
q2 J1=1, K1=0, J2=0, K2=0 J1=1, K1=1, J2=0, K2=0 J1=1, K1=0, J2=0, K2=1 J1=0, K1=1, J2=0, K2=1

Here, we assume that the FSM system states q0, q1, q2 are mapped to the outputs Q1 and Q2 as follows:

FSM states/output coding Q1 Q2
q000
q001
q010

The final mapping from transitions to the biological reporters is then given by:

J1=0, K1=1, J2=1, K2=0 J1=0, K1=0, J2=0, K2=1 J1=1, K1=0, J2=0, K2=1 J1=0, K1=1, J2=0, K2=1 J1=0, K1=1, J2=1, K2=0 J1=0, K1=0, J2=0, K2=1 J1=0, K1=1, J2=0, K2=0 J1=0, K1=0, J2=1, K2=1 J1=1, K1=0, J2=0, K2=0 J1=1, K1=1, J2=0, K2=0 J1=1, K1=0, J2=0, K2=1 J1=0, K1=1, J2=0, K2=1
cyan cyan red cyan cyan cyan yellow green cyan cyan cyan yellow